Building the Ghetto rig – part 3

So we had four cards up and running in the Ghetto rig. We were short a PSU with sufficient PCI-E ports to connect the final two, but recently we got a hold of the cables that made it possible to switch out a Corsair HX1050 from one of our gaming rigs. Then we could connect the last two cards and it eased our worries that a 750W PSU couldn’t handle the stress very well.

new psu

new Corsair hx1050 PSU

new psu in place

new HX1050 PSU in place

We also got two more case fans to drive out the heat from between the two new cards as we did with the ones that were already mounted.

6 cards mounted

6×1060 mounted on board with new case fans

Easy peasy, six cards up and running. When mining with all six 1060s we only use 591 W from the wall!

drawing 591W

Using 591 W of power from the wall while mining with 6×1060

..and we are hitting 130 MH/s, maxing out at 60 C per card.

mining with 6x1060

Mining with 6×1060 using Claymore and reaching 130 MH/s

Since the cards where not standing up by them selves very well we screwed each card to the board.

stabilized gpus

GPUs stabilized by extra screw

And that’s it! The rig is complete. It’s quite portable, somewhat modular, less power consuming than we initially thought and now it remains to be seen if it’s profitable. We are aware that we started this project late into the mining craze and right now profitability mainly depends on the future price of ETH. I hope to follow up with a post on the economics once we have enough real life data on power costs and ether yield.

Building the Ghetto rig – part 2

After waiting for weeks for the Chinese to deliver some sort of sign that they were planning to ship the PCI-E risers I ordered, we tried Amazon instead and had them delivered after a couple of days. That meant that we were ready for the second part of building the Ghetto rig. But first a look at recent events…

The last couple of weeks has been interesting

crypto right now

crypto right now

eth usd 60d chart

eth usd 60d chart

Whats behind the plunge in the graph? Lots of things. ETH was up over 5 000% this year when it hit the all time high around $400 so part if this might be the market making a needed recovery. Early investors are bound to cash in sometime. Also, the ETH price follows its big brother currency Bitcoin closely and recent worries in the Bitcoin community about a possible split and protocol changes affected the whole crypto market. The price is up 33% today at the time of writing, so the next couple of days should be interesting, specially from a trading perspective.

Mounting the risers to the Ghetto miner

But we are not trading right now, we’re mining! We headed out to a hardware store to buy a normal wooden board with the dimensions 20 cm x 100 cm x 2 cm to have something to mount the risers on. We reasoned that wood is cheap, sturdy and easy to work with. It worked out well! I sawed it off to give each riser (and GPU) 10 cm. Pro tip:¬†before screwing anything together, measure it out properly so the cables from the motherboard and PSU will reach the cards.

measuring out the cards

Measuring out the cards on the board

measuring out the risers

giving each riser and card about 10 cm each

We fastened each riser to the board with two screws, four seemed like overkill for the job. To mount this glorious looking GPU board to the mining “case” we drilled two 4 mm holes through the case and the board and screwed it together. This brought some much needed stability to the rig.

Risers installed

Riser cables going in to the motherboard. Get all your cables together before mounting something obscuring on top.

Risers screwed to the board

Risers screwed to the board and board screwed to the case

board to case

board screwed to case

Mounting the cards to the risers

Now we are getting close. Just put the GPUs in their risers and hook up power to the riser and the GPU. We got SATA power cables with the risers but after reading this post on Reddit we were not going to use them. The risers themselves had molex connectors so we just hooked them up directly to the PSU.

cards mounted

cards mounted and hooked up on the board

You might have noticed that we only mounted four of our six cards, and that’s because we haven’t solved the PSU situation yet. The Corsair RX750 we have right now only supports 4 PCI-E cards and it would probably not handle the power load from six cards very well either. But four out of six ain’t half bad and it will be easy to mount the other two cards later since the riser board is prepared for it.

We figured that we needed to manage the heat between the cards so just like last time we slapped some case fans right on to the cards with zip ties. This turned out to be very effective with pushing the hot air out.

fans mounted

Good to go. Case fans mounted on cards.

The moment of truth

Everything was in place, time to hit the button!

fail

the look of failure

Goddammit that’s not what you want to see after a couple of hours working, obscure error messages when trying to boot up. It also said it couldn’t find any keyboard before jumping to that message.

We pulled out all of the risers and booted up without any GPUs (the HDMI is connected to the Intel card on the motherboard) and it worked. I remembered that I read somewhere that you should enable 4G Decoding in BIOS when hooking up many cards to the motherboard, so we did that. Then we installed one card at the time. On card 3 we got a Blue Screen of Death, but hopefully that was just a one time thing while Windows were figuring out what the hell we were doing with so many GPUs. Anyway, all four cards were successfully installed and up and running!

4x1060

Device manager showing 4×1060

Mining

Time to see what this thing could do. We loaded up our mining profile with MSI Afterburner and fired up Claymores miner. We usually mine with Genoil but Claymore is better when testing things out since it outputs easier to interpret hashing speeds.

mining with 4x1060

mining with 4×1060

And there we go. ~90MH/s hash rate and each card using ~80w. Interestingly the cards were running a couple of degrees cooler (54 C – 58 C) than in the first setup. This is probably due to that they are further from each other when mounted to the board as well as the case fans can more effectively push away the hot air.

Next time, installing two more cards and a more powerful (or secondary) PSU.